RollerDrive BT100

With a mechanical performance of 11 Watt and a mechanical commutated motor the RollerDrive BT100 is the optimal solution for application with lower throughputs and less weight. Due to the simplicity of connecting only two wires, BT100 can be controlled and integrated very easy.
There is no specific controller or current limiter needed. With a minimum operational life time of 6000 h, BT100 can convey up to 14 Million boxes.
Operating at a noise level of 47 dB(A), BT100 is the most silent 24VDC drive in the market. RollerDrive BT100 is less electrical noise emitting, fulfilling the requirements of DIN EN 60034-1:1998/A11:2002.


RollerDrive BT100

Characteristics
  • 11 Watts mechanical performance
  • Integral overheat protection
  • 6 different gear ratios available
  • 6000 hours minimum operational time
  • Protection rate IP54 or IP66
  • 47 dB(A) mounted in a conveyor frame
  • 5 m cable length
  • Open cable termination or plug for use with Z-Card BT 24

User Manual Interroll RollerDrive BT100

BT100 Electrical Data
Nominal voltage 24 VDC
Voltage range 16-28 VDC
No load current 0.6 A
Maximum continuous current
 1.3 A
Maximum peak current 4.5 A
Maximum ripple from power supply 5 %
Mechanical Performance
 11 W
Noise emission (mounted) 47 dB(A)
Lifetime under nominal conditions 6000 h
System Efficiency (Drive)
 36 %

BT100 Speed/Load Performance Data

Gear Ratio Nominal Speed
m/s
 Nominal Torque (1.3 A)
Nm
 Peak Torque (4.5 A)
Nm
9 0.90
 0.45
 1.9
9R 0.70
 0.70
 2.6
21 0.40
 0.84
 3
30 0.30
 1.28
 4.4
37 0.20
 1.64
 6.6
37R 0.10
 2.50
 5.6

Minimum RL

 Cartridge  Tube Idler bearing Min RL
9:1 to 9:1 red. No groove 11 mm hexagonal end drilled and tapped M8 203
No groove 11 mm hexagonal spring loaded 246
No groove PolyVee end drilled and tapped M8 228
No groove PolyVee 11 mm hexagonal spring loaded 239
No groove Timing belt/3/8" chain end drilled and tapped 220
Groove 30 60 11 mm hexagonal end drilled and tapped M8 246
Groove 50 80 11 mm hexagonal spring loaded 262
21:1 to 37:1 red. No groove 11 mm hexagonal end drilled and tapped M8 221
No groove 11 mm hexagonal spring loaded 264
No groove PolyVee end drilled and tapped M8 246
No groove PolyVee 11 mm hexagonal spring loaded 257
No groove Timing belt/3/8" chain end drilled and tapped 238
Groove 30 60 11 mm hexagonal end drilled and tapped M8 264
Groove 50 80 11 mm hexagonal spring loaded 280
9:1 to 9:1 red. No groove 11 mm hexagonal end drilled and tapped M8 203
IP66 version Groove 30 60 11 mm hexagonal end drilled and tapped M8 246
21:1 to 37:1 red. No groove 11 mm hexagonal end drilled and tapped M8 218
IP66 version Groove 30 60 11 mm hexagonal end drilled and tapped M8 261
The minimum RL is determinate by the idler bearing and grooves. Maximum RL: 1500 mm.

DriveControl for BT100 RollerDrives
Z-Card
                       

top
© Interroll | Disclaimer